Nippon Pulse Part Numbers
Linear Shaft Motor (Examples)
S080DPL-250st-WP-SO-02 (see chart below)
S160T-200st
S200D-250st-HA
L250Q-1000st
S120Q-200st-SO
S350QPL-500st
|
S = Shaft Type S: Linear Shaft Motor L: Large Air Gap |
250st = Usable Stroke in mm |
|
080 = Shaft Size in mm x 10 4, 8, 12, 16, 20, 25, 32, 35, 42.7, 43.5, 50, 60.5 |
WP = Special Options Blank: Standard WP: Water Resistant HA: Digital Hall effect CE: CE type motor |
|
D = Forcer Size S: Single Winding D: Double Winding T: Triple Winding Q: Quadruple Winding X: Octuple Winding SS: Single Coil Small Forcer DS: Double Coil Small Forcer TS: Triple Coil Small Forcer |
SO = Forcer/Shaft Option Blank: Both FO: Forcer only SO: Shaft only |
|
PL = Parallel Motor Option Blank: Single Motor PL: Parallel Motors |
02 = # of Forcers (two or more) |
Tin-Can Motor (Example)
PF(C)42T-48C1G (1/50)
|
PF(C) = Series Designation PF: Flying lead joint PFC: Connector joint |
C = Coil Rating B: 24V Unipolar C: 12V Unipolar D: 5V Unipolar P: 12V Bipolar Q: 5V Bipolar R: 12V Bipolar (PF35T only) |
| 42 = Outer Diameter in mm |
1 = Magnetic Material 1-Ferrite Anisotropic 3-Ferrite Isotropic 4-Neodymium |
|
T = Type Blank: Standard T: Thin Stack H: High Torque |
G = Gear Head Blank: No gear head G: Gear head |
|
48 = Steps per Revolution 24-15°/step 48-7.5°/step 96-3.75°/step |
1/50 = Gear head ratio with geared models only |
Linear Stepper Motor (Example)
PFCL25-48Q404830
|
PF = Stepper Motor Designation |
Q = Coil rating C: 12V unipolar D: 5V unipolar P: 12V bipolar (PFCL25 only) Q: 5V bipolar R: 12V bipolar (PFL35T only) |
|
C = Connector Type Blank: Flying lead joint C: Connector joint |
4 = Neodymium magnet type |
|
L = Linear step series designation |
048 = Thread Pitch 048: 0.48mm 096: 0.96mm 120: 1.20mm |
|
25 = Motor diameter in mm 25mm 35mm |
30 = Shaft Stroke Length 30: 30mm stroke, 60mm shaft 60: 60mm stroke, 60mm shaft |
|
48 = steps/revolution 24: 15°/step 48: 7.5°/step |
Single Direction Synchronous Motor (Example)
PTM-24BGII100-50/60-2/2.4 CW
|
PTM = Series Designation PTM: Flying lead joint |
100 = Supply Voltage 24, 100, 200 Vac voltage depends on model |
|
24 = Number of Poles 12: Speed is 500rpm w/50Hz Speed is 600rpm w/60Hz 24: Speed is 250rpm w/50Hz Speed is 300rpm w/60Hz |
50/60 = Power Frequency 50, 60, or 50/60Hz |
|
B = Outer Diameter B: 35mm K: 42mm E: 42mm (high output torque) |
2/2.4 = Rotating Speed Line frequency of 60Hz makes the motor speed 1.2 times higher than 50Hz |
|
G = Gear Head Blank: No gear head G: Gear head intergrated |
CW = Direction CW - Clockwise CCW - Counterclockwise |
|
PTM-24BGII only Denotes BG gear type II |
Dual Direction Synchronous Motor (Example)
PTM(C)-24F34G1/2
|
PTM(C) = Series Designation PTM: Flying lead joint type PTMC: Connector joint type |
4 = Magnet Type Blank: Anisotropic 3: Isotropic 4: Neodymium 5: Plastic |
|
24 = Number of Poles 12: Speed is 500 rpm w/50Hz Speed is 600 rpm w/ 60Hz 24: Speed is 250 rpm w/ 50Hz Speed is 300 rpm w/ 60Hz |
G = Gear Head Blank: No Gear Head G: Gear Head Integrated |
|
F = Outer Diameter (Type) P: 22mm, M: 35mm, T: 35mm (thin) H: 12mm, S: 42mm (thin) F: 55mm, R: 55mm (w/ connector) |
1/2 = Gear Ratio |
|
3 = Coil Specification Blank: Standard Coil (continuous for 24, 100, 200 Vac) 1-18: Coil # for specific rating |
|
Hybrid Motor (Example)
PR28H-32-0954JAG 1/5
| PR = Series Designation |
4 = Number of Lead Wires 4: Bipolar 8: Bipolar |
|
28 = Motor Frame Size 20 = 20mm 28 = 28mm 42 = 42mm 57 = 57mm |
J = Step Angle M: 0.9° J: 1.8° |
|
H = Motor Type H = High Torque S = Standard Torque |
A = Shaft Type A: Single B: Double |
|
32 = Motor Case Length PR20 = 30mm, 42 PR28 = 32, 45, 51 PR42 = 33, 38, 47 PR57 = 41, 56 |
G = Gearhead gearhead attached |
|
095 = Coil Winding Type Amps per phase |
1/5 = Gearhead ratio |
PRO Series Motor (Example)
PRO42AP-3810-Exxx
| PRO = Series Designation |
38 = Motor Length PRO42 - 40mm, 48mm, 60mm PRO57 - 43mm, 56mm, 78mm |
|
42 = Frame Size 42mm (NEMA 17) 57mm (NEMA 23) |
10 = Current |
|
AP = Controller/Driver Type AP = Advanced type, pulse/dir BP = Basic type, pulse/dir |
Exxx = Encoder w/# count |
Need Help? Contact Nippon Pulse Sales Engineers
Our sales engineers can help you decide what will work best for your application.
- Phone Number
- 1-540-633-1677
- info@nipponpulse.com